西南山地区域森林火险综合预报模型研究——以重庆市为例

森林火灾严重破坏森林生态系统的结构和功能,针对其风险预报开展研究具有重要的理论意义和应用价值。通过融合气象、地表覆盖和人类活动等要素的方式构建森林火险综合预报模型,是西南山地区域森林火险综合预报业务化应用的重要发展方向。基于《森林火险气象等级》国家标准(GB/T 36743-2018),本文研究首先构建了重庆市森林火险气象风险预报模型。然后通过融合可燃物因素和人为因素的方式,进一步构建重庆市森林火险综合预报模型。最后利用历史火点数据针对上述两类模型的精度进行对比和分析。研究结果表明:重庆市森林火灾发生次数较多,且呈现出季节性规律;重庆市森林火灾的发生不仅受到气象条件的影响,而且受到地表覆盖和人类活动等多种要素条件的共同影响;与森林火险气象风险预报结果相比,森林火险综合预报结果在空间分布上具有更高的精细程度;森林火险综合预报模型能有效提高森林火险等级预报精度。     

钙钛矿型催化剂催化湿式氧化处理煤气化废水纳滤浓缩液

采用溶胶-凝胶法制备了Mn掺杂钙钛矿型催化剂LaFexMn1-xO3，并以其为催化剂催化湿式双氧水氧化处理煤气化废水纳滤浓缩液。采用XRD，SEM，FTIR技术对催化剂进行了表征。表征结果显示：制备的催化剂均具有标准的钙钛矿型结构，其中，LaFe0.9Mn0.1O3的结构稳定，比表面积大。实验结果表明：制备的催化剂中LaFe0.9Mn0.1O3的催化活性最高，且稳定性好，连续使用5次后催化活性未见明显减弱；在H2O2投加量3.0 g/L、n（H2O2）∶n（LaFe0.9Mn0.1O3）=12∶1、反应温度160 ℃、反应压力1 MPa、浓缩液pH 3、反应时间60 min的最优条件下，COD、UV254和TOC的去除率分别达到80.9%、95.2%和68.0%，BOD5/COD由0.02提升至0.40，可生化性大幅提高。     

Safety assessment of the film boiling chemical vapor infiltration (FB-CVI) process through a system-theoretic accident model and process (STAMP)

Film boiling chemical vapor infiltration (FB-CVI) is considered as one of the fastest process methodologies for manufacturing carbon-carbon (C–C) composite products and possesses various advantages compared to conventional methodologies. However, there are safety concerns associated with this process for large-scale manufacturing, mainly owing to the intrinsic nature of the precursor and the process conditions. Considering the multifunctional interactions of the various systems during the process, a system-theoretic process analysis (STPA)/system theoretic accident model and process (STAMP) model is used to perform a safety analysis of the hazardous states of the FB-CVI process at the system level. As a case study, the FB-CVI process equipment employed for the manufacturing of C–C composites is considered. The safety constraints present in the system are assessed for adequacy through a hazard analysis by STPA/STAMP. The analysis through STPA/STAMP demonstrated the capability to create proactive strategies for the design and realization of process equipment that can be employed to manufacture C–C composite products through the FB-CVI process.     

γ-Al2O3负载多金属复合催化剂选择性催化还原烟气脱硝

以γ-Al₂O₃作为载体，先后负载CeO₂，MnC₂O₄，Fe（NO₃）₃，CrO₃，Ni（NO₃）₂，NH₄VO₃等多种金属组分制备γ-Al₂O₃负载多金属复合催化剂，并用于模拟烟气的选择性催化还原脱硝。通过SEM和XRD技术对催化剂进行了表征。表征结果显示：Fe，Mn，Cr的添加能增加催化剂的低温催化活性、提高催化剂的N₂选择性;γ-Al₂O₃对活性金属氧化物的负载效果良好。实验结果表明：各金属化合物的最佳加入量为 w（MnC₂O₄·2H₂O）=20%，w（Fe（NO₃）₃·9H₂O）=15%，w（CrO₃）=10%，w（Ni（NO₃）₂·6H₂O）=5%，w（NH₄VO₃）=10%，w（CeO₂）=5%，w（γ-Al₂O₃）=35%;以在最佳正交实验条件下制得的γ-Al₂O₃负载多金属复合物为催化剂，在脱硝反应温度为205 ℃的条件下，NO转化率为96.7%;γ-Al₂O₃负载多金属复合催化剂经5次重复使用，NO转化率仍可稳定在94%左右。     

基于RFPA2D复合局部挠曲岩体数值模拟

为研究复合局部挠曲岩体强度特征以及破坏规律，采用岩石真实破裂软件RFPA^2D，对水平层面挠曲30°，45°，60°，75°的复合岩体进行单轴压缩试验模拟。模拟结果表明:挠曲角为30°，45°，60°，75°的复合岩体破坏面几乎与挠曲段夹层重合，其挠曲端部均产生了垂直于挠曲段夹层的裂纹；复合单斜岩体与复合挠曲岩体破坏面的形成因素大致相同，夹层强度是2种岩体失稳的主要因素；复合挠曲岩体单轴抗压强度随挠曲角增大同样呈“U”型变化，与单斜岩体变化趋势一致；当水平层状岩体发生挠曲后，其单轴抗压强度减小，当挠曲角为60°时，强度降低25.19%，当挠曲角为75°时，强度降低0.17%。；随着均质系数m的增大，复合挠曲岩体单轴抗压强度以及轴向应变均出现逐渐递增的趋势，且不同m值，其岩体裂隙扩展方式具有明显差别。     

Adsorption characteristics and mechanism of Cr （Ⅵ） on chitoan-yttrium porous microsphere

以壳聚糖和Y2（OH）5NO3为原料通过乳液交联法制备了壳聚糖-钇（Ch—Y）复合微球,通过扫描电镜、透射电镜、X射线衍射、红外光谱等方法对其表面形貌、结构进行了表征.探讨了溶液的pH值、反应时间、投加量、离子初始浓度对其吸附性能的影响.研究结果表明,壳聚糖-钇（Ch—Y）复合微球在pH值为3的酸性环境中对Cr（Ⅵ）保持了较高的吸附能力,吸附容量为52.39mg·g-1,其吸附行为符合Langmuir吸附等温模型;通过吸附机理的研究,发现壳聚糖-钇（Ch—Y）对Cr（Ⅵ）吸附是化学吸附静电吸附协同氧化Cr（Ⅵ）离子作用来实现的.     

纳米TiO_2-Al_2O_3负载CuMnO_x对甲苯的催化燃烧

研究采用改进的溶胶-凝胶法制备了TiO2-Al2O3复合载体,并用浸渍法制备CuMnOX/TiO2-Al2O3催化剂,通过对甲苯废气催化燃烧的实验,分别考察了Cu-Mn负载量、Cu/Mn摩尔比、焙烧温度及载体对催化剂制备过程及催化剂活性的影响。实验结果表明:活性组分负载量25%,铜锰活性组分的配比Cu:Mn=1:2,焙烧温度500℃是浸渍法制备CuMnOX/TiO2-Al2O3催化剂较佳的工艺条件;XRD衍射图谱表明,500℃下铜锰尖晶石的存在是催化剂催化活性优良的主要原因;由复合载体制备的CuMnOX/TiO2-Al2O3催化剂比单一载体制备的CuMnOX/Al2O3催化剂具有更高的甲苯转化率,其T99比单一载体要低20℃以上。     

基于响应面优化条件下柚皮对Pb2+的吸附

采用Plackett-Burman(P-B)法和中心复合设计(Central Composite Design,简称CCD)对影响柚皮吸附Pb2+的6个条件进行筛选优化.P-B实验设计与统计学分析表明:pH值、Pb2+初始浓度、吸附剂用量是影响吸附率的3个关键因素.以吸附率为响应目标,对3因素进行中心复合设计,并经响应面法优化分析得到影响吸附率的二阶模型,确定了Pb2+吸附实验的最优操作条件:pH值5.4.Pb2+初始浓度为265.86mg·L-1,吸附剂用量为2.56 g·L-1,实测吸附率达到92.47%,吸附量为96.01 mg·g-1;整个吸附过程吸附剂柚皮没有经过任何化学预处理.效果优于一般的天然吸附剂.研究结果表明,柚皮是一种很具潜力的环保型廉价吸附剂.     

Analysis of diffusion-adsorption equivalency of landfill liner systems for organic contaminants

The equivalence between multilayered barriers regarding diffusion and adsorption is analyzed by means of an analytical method. The bottom boundary of the liner system is defined by assuming concentration continuous and flux continuous conditions of the contaminant between the bottom liner layer and the underlying soil. Five different liner systems were compared in terms of solute breakthrough time. The results of the analysis show that breakthrough time of the hydrophobic organic compounds for a 2-meter-thick compacted clay liner (CCL) can be 3-4 orders of magnitude greater than the breakthrough time for a geosynthetic clay liner (GCL) composite liner. The GM/GCL and GM/CCL composite liner systems provide a better diffusion barrier for the hydrophilic organic compounds than that for the hydrophobic compounds due to their different Henry's coefficient. The calculated breakthrough times of the organic contaminants for the Chinese standard liner systems were found to be generally greater than those for the GCL alternatives, for the specific conditions examined. If the distribution coefficient increases to 2.8 for the hydrophobic compounds or 1.0 for the hydrophilic compounds, the thickness of the attenuation layer needed to achieve the same breakthrough time as the standard liner systems can be reduced by a factor of about 1.9-2.4. As far as diffusive and adsorption contaminant transport are concerned, GM or GCL is less effective than CCL.     

Photocatalytic degradation of methyl orange over ITO/CdS/ZnO interface composite films

ITO/CdS/ZnO interface composite films were successfully prepared by subsequent electrodeposition of CdS and ZnO onto indium tin oxide (ITO) glass substrates. The obtained ITO/CdS/ZnO composite films were characterized with X-ray diffraction (XRD), scanning electron microscopy (SEM), and UV-Vis spectroscopy. The photocatalytic activity of ITO/CdS/ZnO composite films were investigated using methyl orange (MO) as a model organic compound under UV light irradiation. The influence of operating parameters on MO degradation including initial concentration of MO, pH value of solution, and inorganic anion species over the composite films were examined. A blue shift of absorption threshold was observed for the ITO/CdS/ZnO film in comparison with ITO/ZnO film. ITO/CdS/ZnO composite films prepared under specific conditions showed a higher photocatalytic activity than that of ITO/ZnO films. It was also found that the photocatalytic degradation of MO on the composite filing followed pseudo-first order kinetics.